Reduce Wheelhop, bushing deflection, and cradle movement on your 2016-newer Chevrolet Camaro with a Cradle Bushing Lockout Kit from BMR Suspension. Built from CNC-machines Delrin, laser-cut stainless steel, and billet aluminum, BMR?s BK063 Cradle Bushing Lockout Kit is designed to greatly reduce cradle bushing deflection, which is one of the biggest causes of wheelhop. BMR?s BK063?s Delrin upper bushing inserts are CNC-machined and specifically designed to fill the voids in the factory bushings (front and rear). The additional hollow space is filled with CNC-aluminum ?bullet? inserts. The kit is finished with laser-cut stainless steel washers that capture the lower Delrin inserts and prevent up and down movement. By filling the voids in the bushings, deflection is greatly reduced, allowing more power and torque to be transferred to the ground instead of being absorbed by the chassis. BMR Suspension designed the BK063 Cradle Bushing Lockout Kit for street performance, drag race, and handling applications. This 100% bolt-on kit use existing boltholes and hardware, allowing for easy installation with simple hand tools. Once installed, the Cradle Bushing Lockout Kit minimized bushing and cradle deflection with nearly no change in NVH. (During BMR?s testing, no change in NVH was observed without accompanying modifications.) BMR Suspension?s BK063 Cradle Bushing Lockout Kit is the only part you need to affordably and effectively lessen wheelhop, bushing deflection, and cradle movement. Throughout testing, BMR has seen about an 80%-90% reduction in fore/aft and lateral cradle bushing deflection. A car with no other mods and stock tires that isn?t driven overly hard is going to see a 90% or higher reduction, while a more race oriented Camaros with sticky tires will see slightly less of a reduction. Launching the test vehicle at over 7,000 rpm on drag radials, BMR saw about an 80% reduction in bushing deflection.
100% bolt-on design;No fabrication needed;Installs with simple hand tools;CNC-machined Delrin Bushing Inserts;CNC-machined 6061-T6 billet aluminum bushing insert ?bullets?;Laser-cut stainless steel lower bushing support washers;Greatly reduces stock bushing deflection, wheelhop, and cradle deflection ;Used factory boltholes and hardware;Proudly designed in the U.S.A.;Proudly built in the U.S.A.
This 100% bolt-on kit use existing boltholes and hardware, allowing for easy installation with simple hand tools. Once installed, the Cradle Bushing Lockout Kit minimized bushing and cradle deflection with nearly no change in NVH.
BMR 16-17 6th Gen Camaro Rear Cradle Lockout Bushing Kit - Black
Bushing Kit, Rear Cradle, Lockout
Suspension Subframe Bushing Kit
BMR Suspension - BK062
Rear Cradle Lockout
Do you need performance suspension kits: A-Arms, control arms, brake kits, bushings and end links, drive shafts, suspension kits and a host of other aftermarket parts? LMPerformance has the best BMR Suspension Products for your aftermarket needs. BMR Suspension products are innovative in design, are of quality construction and are affordable.
BMR Suspension products are proudly Made In USA and BMR uses American-made DOM and chrome-moly steel. BMR performance suspension kits manufacture its parts in house and fixture-welds every part to assure excellent quality. We cut, bend, notch, drill, and mill our tubular components from American-made DOM and chrome-moly steel. Every product is fixture-welded to maintain consistent quality. We bead-blast our parts and then powdercoat them on our own powdercoating line. Then we assemble and package the products in our assembly department. By manufacturing our products in house, BMR can control the quality at every stage of the manufacturing process. BMR Suspension products and performance suspension kits fit and work so well because they are street driven and track tested on BMR project vehicles.
BMR performance suspension kits currently offers Suspension, Chassis, and Drivetrain products for over 16 different vehicles including but not limited to Chevy Camaro 1969-2016+, Pontiac G8 and Pontiac GTO, Chevy SS, Classic GM Muscle cars such as the Chevelle, GTO, A-Body, B-Body, G-body, and X-Body, Ford Mustangs 1979-2016+. They are the leading suspension manufacturer in many market segments.
Let LMPerformance help you find the BMR suspension parts you need. Whether you are in the market for swaybars, a-arms, lower control arms, shock braces, subframe connectors, drive shaft loops, pan hard bars, torque arms, crossmembers, and more you will find a great price at lmperformance.com.
You can trace the roots of BMR back to 1998 when they were far sighted enough to determine that suspension products that were innovative and affordable were lacking in the marketplace and they were clever enough to use this knowledge to develop the incomparable company they are today in their facility in Tampa, Florida. They leave no stone unturned in the development and production of their products to assure you are totally satisfied with what you purchase and they are able to do this because all of their suspension products go through rigorous testing by being street and track tested on BMR project vehicles. The multiplicity of project vehicles at their disposal contributes greatly to their success in this endeavor but even more impressive is the fact that nearly every BMR employee is a racer or hot rod aficionado with a love for racing and a desire to give you a quintessential product. Folks like this know just how critical the suspension products are on your car, whether it be for racing or street driving and they work diligently to give you the best in design and manufacturing and try to do this so that they can give you a part that is affordable, functional and long lasting. When you choose a suspension product from BMR you can feel confident in your decision because the product was created by people who know the product and know that it can function in a variety of situations because they have driven it where it counts-on the road.
IMAGES: Images may be a representation and may not reflect the actual product.
California Residents: Prop 65 WARNING: This product MAY contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For more information, visit www.P65Warnings.ca.gov
California Residents: TIRE WARNING: LMPerformance will not ship Tires to California.
Legal: Some or all of these parts may not comply with Federal, State, Province, and/or Local laws, ordinances, and regulations. Buyer takes all responsibility to ensure that any modifications or upgrades that have done conform to all applicable laws and regulations for road use, especially pertaining to safety and emissions. LMPerformance is not responsible for buyer not complying with Federal, State, Province, and/or Local laws, ordinances, and regulations. This policy shall be in force for all past, current, and future purchases from LMPerformance, Inc. LMPerformance will not ship ANY non-CARB compliant products to California where California requires products to be CARB certified such as Catalytic Converters and Induction Kits.
FREE SHIPPING: Please note FREE Shipping refers to shipping within the contiguous continental US only. All other locations extra. Some items that require Truck Freight Delivery will require a Truck Freight surcharge. This surcharge is still a discounted shipping amount that is lower then the actual truck freight shipping charge that is charged to LMP. LMP will try to still give the lowest price possible for truck freight items.
IMAGES: Images may be a representation and may not reflect the actual product. Examples would be SPEC stage 3 clutch kits which all use the same photo.
TYPOS: LMPerformance tries to present the best most accurate information on our website. Sometimes we get mistakes in product information sent from vendors such as typos. We can not be responsible for these typos, if you see something that does not look right please let us know before ordering so we can double check for you first. LMPerformance will not pay for typos in any way, monetarily or otherwise.
SPECIAL ORDER ITEMS: Some items are special ordered and may not be returnable, or even cancellable as they are going into production specifically because you ordered them. Special ordered items can have a 5-35% cancelation fee.
Cancellations: Instock orders cannot be canceled due to our automated ordering & fast shipping system. To keep our prices low, all cancelations are subject to a 5% cancelation fee to cover transaction processing fees. We reserve the right to charge up to a 10% cancellation fee for cancelled orders due to merchant fees, special order fees and the cost of processing and shipping orders.When you request a cancellation of an order or a part, please note that it may take time for a manufacturer to cancel an order if the order is drop-shipped. We also have to confirm that the product has not shipped. If the product has shipped then this must be processed as a return.Also note that sometimes products ship more quickly than expected, so we recommend that you do not purchase alternative products until receiving final confirmation of the cancellation.
Returns:We cannot accept returns on parts that have been used or installed. No returns will be accepted after 30 days. All Returns must be in original packaging. Prior authorization must be given before any return can be made. Up to a 25% Restocking Fee may apply. Special orders may be subject to Additional Manufacturer Restock Fees as well. Shipping cost will not be refunded.Hoods as well as PCM Programmers may not be returned unless defective and only for replacement. ALL returns must be first filed using our online form found here: https://www.lmperformance.com/returns.
Lost Order ClaimsAll lost order/package claims must be made within 5 days of the shipping date or tracking information delivery date. All claimes made after this date will not be accepted due to Shipping companies policies of filing loss claims.
Damaged Items or Incorrect Items: Please contact us right away if your item has been damaged in shipping or are incorrect. Please note that we will ship replacement items the same method of shipping the order was originally placed for. LMPerformance can not ship packages overnight at our cost if the original shipping was not also overnight. Claims must be filed in order for replacement parts to be shipped.
Warranties:Any warranty claims must be placed with the manufacturer. All of the products sold by LMPerformance, regardless of the manufacturer, are designed for Racing and Performance applications. Many of our manufacturers offer NO WARRANTY on their products, either stated or implied, due to the unusual stresses placed on the parts and because we have no control over how they are installed and used. Many of these products are designed for off-road use only and are not legal for use on public highways. If you have a question about the warranty on a specific product, please e-mail or call us. Buyer assumes all risk and liability associated with these products.
Installation:We are not responsible for or any costs associated with the installation or the improper installation of any products. Purchaser assumes the risk associated with the installation of products. We, along with the manufacturer of each product are not responsible for any direct or indirect damage to the vehicle, personal, or costs incurred from the use of products.
Starting at 0% Order Now, Pay Later Learn More.
