Edelbrock Pro Flo 4 EFI System Seq Port Chrysler Gen II Hemi 426-572 950 Max HP 60lb/hr Satin Finish 35670

Our new Pro-Flo 4 Dual-Quad HEMI EFI System #35670 is intended for use with1964-71 Mopar Gen II 426-572 HEMI engines operating in the 2;500-6;500+RPM range. This EFI incorporates a single-plane Air-Gap manifold with dual square-bore 4150-style throttle bodies that bolts directly onto vehicles with a shaker hood. The Dual-Quad HEMI EFI manifold is compatible with factory-style cylinder heads but optimized for use with our Victor Jr. HEMI heads. Manifold comes preassembled and ready to run with throttle bodies; 60 lb/hr injectors and fuel rails. Also included is a single-connection distributor designed to work specifically with Pro-Flo 4 providing fully sequential-port injection and infinite control over ignition and fuel events under all conditions. This system is rated for 825 horsepower at 43 PSI with all supporting sensors; ECU; wire harnesses and 7-inch Android tablet included for a streamlined installation. Key advancements of Pro-Flo 4 EFI are its Self-Calibrating Fuel Map Technology; Wide-Band O2 Closed Loop Mixture Control; and new low-profile ECU with faster processor and upgraded Bluetooth chip for reliable connectivity with the E-Tuner app that comes preinstalled on the tablet. The E-Tuner includes a Setup Wizard to guide you through setup and provides fuel and spark adjustability for complete control over the system. Pro-Flo 4 EFI does not require laptop tuning. Minimal setup and tuning adjustments are required with base calibrations provided in the software. The ECU is self-learning and will continually adjust the calibration to get the maximum performance out of your engine by maintaining a specified target air-fuel ratio as you drive. Our E-Tuner provides the ability to fine-tune air-fuel ratios; ignition curve; idle speed; acceleration fuel; fans; rev-limiter and more. Multiple displays let you monitor engine performance in real-time from inside or outside of the vehicle while retaining the simplicity that Pro-Flo 4 systems are known for.

When choosing to upgrade your engine to modern fuel injection, look no further than Edelbrock's Pro-Flo 4 EFI systems. Edelbrock has been delivering the best combination of dyno proven electronic fuel injection performance for over 40 years. Pro-Flo 4 is not just a replacement for your carburetor, it's a complete engineered system that provides the ultimate in performance, drivability and quality. These easy to use, self-learning EFI systems feature an all new ECU pre-loaded with 80 dyno-tuned calibrations that support popular engine configurations up to 800 hp. Combined with the enhanced E-Tuner 4 App's easy to use setup wizard; you get plug and play performance without the need of a laptop or costly dyno tuning sessions. Pro-Flo 4 EFI systems are the most complete systems available on the market, giving you what you need to upgrade to powerful and efficient fuel injection for your vehicle. Pro-Flo 4 EFI systems are the best value for your dollar! ** INSTALLATION NOTE: These systems will require a high pressure EFI compatible fuel delivery system. Fuel delivery kits are available and sold separately. LS kits will require a coil harness which is sold separately. 24(x) reluctor applications will require #37-1633 and 58(x) reluctor applications will require #37-1632. #35760/#35770 manifold height: 4.58. #35780 Manifold height: 4.58. #35700/#35710 manifold height: 4.95. #35740/#35750 manifold height: 7.40. #35830/#35840 manifold height: 5.90. #35850/#35860 manifold height: 5.90. #359300 manifold height: 6.30. #335910 manifold height: 6.10. #35930/#35940 manifold height: 6.35. #35950 manifold height: 6.25. #35960 manifold height: 6.49. #35970/#35980 manifold height: 6.60. Throttle body height: 2.25

Pro-Flo 4 EFI; Electronic Fuel Injection; Sequential Port EFI; Direct-port EFI; Edelbrock; Edelbrock EFI; Chrysler Hemi; Mopar Hemi; 426 Hemi; Elephant engine; TBI; Throttle Body Injection; FiTech; Holley; Sniper TBI; Fast EFI; MSD EFI; Atomic; Quick Fuel EFI; Power Adder; Intake systems; Fuel systems; The Best EFI; High-Performance

Pf4 Fuel Injection Kit Dual Quad Sequential Port Chrysler Gen Ii Hemi 426-572 950 Max Hp 60 Lbhr Injectors Satin.

PF4 FUEL INJECTION KIT DUAL QUAD SEQUENTIAL PORT CHRYSLER GEN II HEMI 426-572 950 MAX HP 60 LbHr INJECTORS SATIN

Edelbrock Pro Flo 4 EFI System Seq Port Chrysler Gen II Hemi 426-572 950 Max HP 60lb/hr Satin Finish

PF4 FUEL INJECTION KIT DUAL QUAD SEQUENTIAL PORT CHRYSLER GEN II HEMI 426-572 95

Pro-Flo 4 EFI Traditional 4150-Style Kit #35670 For Chrysler HEMI Gen II 426-572

Edelbrock Pro-Flo 4 EFI #35670 for Chrysler Gen II 426-572 HEMI

Edelbrock Fuel Injection

Fuel Injector Kit

Edelbrock no longer supplies screens with their EFI kits. Instead you use their Free App. The exclusive Edelbrock E-Tuner 4 app is Free and Available for Android and IOS based smart phone or tablet.

If you need a throttle body, lower or upper control arm, panhard rod or shock tower brace for your Camaro, Firebird or Mustang you can't go wrong with one of the Edelbrock performer intake parts, or Edelbrock manifolds from LMPerformance.com. You will get a top quality product, carefully selected by the LMPerformance staff.

LMPerformance selected Edelbrock performer intake products, and Edelbrock manifolds for its customers because they know you can trust a company that has been in business since 1938 and has manufactured its core products in the USA with a guarantee of quality and performance. The quality of the Edelbrock throttle body can be seen in the larger than stock throttle bore that allows increased air volume and more power. In addition, the Edelbrock throttle body has sealed throttle shaft ball bearings to allow for safe, smooth operation. To assure top performance Edelbrock includes on most of its applications (check listings for applications on their web site) a brand new throttle position sensor (TPS) that is pre-installed and factory set with the same high-tech equipment used by Original Equipment manufacturers.

The EDELBROCK Company can trace its beginnings to a simple thing like the purchase of a 1932 Ford Roadster by its founder VIC EDELBROCK, SR whose purchase was the inspiration for the original EDELBROCK performer intake manifold, the “SLINGSHOT” and then ultimately the introduction of the EDELBROCK POWER AND SPEED EQUIPMENT catalog making the EDELBROCK manifold parts available to the public. The company continued to grow over the years and subsequently the company opened their own facility and began dyno testing on a small block Chevrolet engine which culminated in the production of the three carb Edelbrock intake manifold, the six-carb Ram Log manifold and the Cross Ram manifold and later the company went on to achieve even greater success with the C-4B manifold, the Tunnel Ram, Tarantula and STREETMASTER manifolds. From these humble beginnings has developed a company that now has six locations throughout the United States with facilities for Research and Development, Manufacturing, Primo Testing, Advertising and Technical Support and it is all the result of one man’s love for racing and his determination to make something better and not be content with the mundane-he wanted to win races after all. Following in this path of demanding excellence the EDELBROCK intake Company continues to discover and improve high performance products today for car enthusiasts like you with things like the EDELBROCK Rear Lower Control Arm for your Mustang 2005-11 V6 that was constructed to improve your Mustang’s ability to turn more easily and stabilize the rear suspension because they know that ordinary control arms installed when your car was built cannot accommodate the aggressive driving Mustang owners who race witness and they were determined to give you something better. Find these and other outstanding EDELBROCK performance parts on the LMPERFORMANCE web site and see how an aftermarket performance part by EDELBROCK can make a difference in your car’s handling.

Since 2001 the folks at LMPerformance.com have researched the best quality parts for your performance vehicle. This research led them to the decision to carry the Edelbrock throttle body, Edelbrock performer intake, Edelbrock manifold, lower and upper control arm, panhard rod and shock tower brace and to offer them to their customers at the best price. Looking for more great intake products? Check out this Trailblazer SS Cold Air Intake.

If you need a throttle body, lower or upper control arm, panhard rod or shock tower brace for your Camaro, Firebird or Mustang you can't go wrong with one of the Edelbrock parts from LMPerformance.com. You will get a top quality product, carefully selected by the LMPerformance staff.

* This is a universal item without fitment details. Please make sure this item is for your application. LMP does not guarantee fitment on universal items.

IMAGES: Images may be a representation and may not reflect the actual product.