JLT Cold Air Intake Hellcat Challenger 6.2L with White Dry Filter, JLT Cold Air Intake Hellcat Charger 6.2L with White Dry Filter
JLT Cold Air Intake Hellcat Challenger 6.2L with White Dry Filter, JLT Cold Air Intake Hellcat Charger 6.2L with White Dry Filter
This intake includes a White Dry Filter. Dry Filters have comparable airflow to oiled cotton filters with the same great protection. these Last for up to 30, 000 miles of highway driving. Extend the life of the filter using compressed air.
Here kitty kitty! JLT HELLCAT Cold Air Intake (2015-19 6.2L Charger/Challenger)15-20 RWHP and No Tune Required!JLT has jumped into the Hellcat intake market with both feet. We have owned a 2016 Hellcat Charger for nearly a year now and have been testing and designing this kit the entire time.This kit includes a fully Roto Molded airbox that uses the factory fresh air (Ram Air) inlet from the grille/headlight that also seals to the hood. We feel this is the key component that puts our kit well above the rest. Not only does this box help keep inlet air temps down by blocking the filter from hot engine heat, it also helps hold in the cool air getting rammed in from the inlet creating a high pressure area around the filter.Speaking of the filter, our filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1 deep pleats for more surface area than filters that look much bigger.The intake tube is roto molded plastic with a huge 125mm for superior airflow and NO heat soak like metal tubes.With a mouth of 4.5 at the throttle body end, it is ready for any larger throttle bodies that may come in the future.MAF and IAT adaptor plates2015/16 Hellcats have a Mass Air Flow sensor and 2017-2019 have an Inlet Air Temp sensor. We designed our kit to work with BOTH. Included in each kit are CNC machined aluminum plates, gasket and stainless screws to adapt to either model years.HEAT SHIELDIncludes new roto molded plastic heat shield to block engine heat at idle and low speed.RAIN SHIELDSEach kit comes with custom designed and water jet cut Lexan shields that bolt to the hood grille. Not only do they keep rain from the filter, they allow the cooler rammed air to stay in the box around the filter VS just being pushed out of the grille.FEATURES:
Incorporates fresh air inlet from the grill.Uses a large area to make sure the filter has tons of cool air.Kit includes:JLT Plastic Intake TubeSilicone Reducer5x7 S&B Powerstack Air FilterRoto molded Heat ShieldJLT MAF adaptor plateJLT IAT adaptor plateJLT Charger Rain ShieldJLT Challenger Rain ShieldHD Clamps & all needed hardware2019 Hellcat PCV KitGAINS AND TESTING15-20 RWHP can be expected on a stock Hellcat25-30+ can be expected on a pulley and tuned Hellcat
TUNINGNo tuning required
EASY INSTALLThe design, detailed instructions and online video (see below) helps make this an easy install (see Instructions & Videos tabs to download / view).
AIR FILTER OPTIONS - OIL OR DRYWe use only the best air filters made by S&B to our specifications.For years we only used oiled filters, but dry filter technology has been proven and is now a popular option.
Should I choose a Dry Disposable or Cotton Oiled Filter?Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it.
Dry:Comparable airflow to oiled cotton filters with the same great protection.Last for up to 30, 000 miles of highway driving. Extend the life of the filter using compressed air.
Oil: Oiled filters can last forever as long as you properly clean and re-oil it.Oil filters are available in red or blue and Dry filters are white.
RACE FILTER:The Race filter is an optional filter, this filter IS NOT FOR STREET USE! It's no filtering media, with prolonged use it will allow contaminated that can damage your engine! JLT Performance will not be responsible for any damage from use of Race filter. Customer assumes all risk!
MAINTENANCETo properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again.
JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!
TESTINGWe wanted to do as much testing as possible, so we sent kits to some of the best in the Hellcat business.
*This product is NOT CARB (California Air Resource Board) Exempt. It is not for legal sale or use in the state of CA or any other states adopting CA emission standards and require a CA Executive Order (EO) number. Any orders placed for this item with a CA ship to address will be cancelled.
CARB E.O. # D-761-4 and will include a CARB decal with each kit starting March 3rd, 2020
Kit Includes a DRY FILTER
JLT cold air intakes are made right here in the USA. JLT PERFORMANCE was founded in 2004 and is located in Chesapeake, Virginia where they manufacture not only primo cold air intakes but impressive oil separators for late model Mustangs, Camaros, Mopars and Ford Trucks.
You know that a cold air intake serves the purpose of moving the air filter outside of the engine compartment and away from unnecessary heat thus it allows cooler air and more oxygen into your car’s combustion chamber and as a consequence your car has more power. But not all cold air intakes are created equal and JLT cold air intakes like the direct replacements for 1996-2004 Mustangs, 1997-2003, 2015-2917 Ford trucks and 2005-2018 Mopar cars will require no tuning. If you have a 2005 and newer Ford or Camaro because JLT has complete packages with tuners and custom tunes so you can install it all at home in less than one hour. You won’t find any choke points nor will there be any accordion style bends resulting in a minimum of restriction with these air intakes and because the JLT intakes only draw air from outside the engine bay your car’s engine gets maximum air density which should improve mileage under almost all driving conditions.
JLT also developed a uniquely designed oil separator that filters and separates the oil in the vapor so that it is deposited into a catch can rather than in your car’s intake system. Although the oil separator will work on any engine JLT looked out for their Ford, Mopar and GM customers in particular by designing a plug and play set up that will work on most applications with PCV lines already attached so installation should only take about a minute..
IMAGES: Images may be a representation and may not reflect the actual product.
California Residents: Prop 65 WARNING: This product MAY contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For more information, visit www.P65Warnings.ca.gov
California Residents: TIRE WARNING: LMPerformance will not ship Tires to California.
Legal: Some or all of these parts may not comply with Federal, State, Province, and/or Local laws, ordinances, and regulations. Buyer takes all responsibility to ensure that any modifications or upgrades that have done conform to all applicable laws and regulations for road use, especially pertaining to safety and emissions. LMPerformance is not responsible for buyer not complying with Federal, State, Province, and/or Local laws, ordinances, and regulations. This policy shall be in force for all past, current, and future purchases from LMPerformance, Inc. LMPerformance will not ship ANY non-CARB compliant products to California where California requires products to be CARB certified such as Catalytic Converters and Induction Kits.
FREE SHIPPING: Please note FREE Shipping refers to shipping within the contiguous continental US only. All other locations extra. Some items that require Truck Freight Delivery will require a Truck Freight surcharge. This surcharge is still a discounted shipping amount that is lower then the actual truck freight shipping charge that is charged to LMP. LMP will try to still give the lowest price possible for truck freight items.
IMAGES: Images may be a representation and may not reflect the actual product. Examples would be SPEC stage 3 clutch kits which all use the same photo.
TYPOS: LMPerformance tries to present the best most accurate information on our website. Sometimes we get mistakes in product information sent from vendors such as typos. We can not be responsible for these typos, if you see something that does not look right please let us know before ordering so we can double check for you first. LMPerformance will not pay for typos in any way, monetarily or otherwise.
SPECIAL ORDER ITEMS: Some items are special ordered and may not be returnable, or even cancellable as they are going into production specifically because you ordered them. Special ordered items can have a 5-35% cancelation fee.
Cancellations: Instock orders cannot be canceled due to our automated ordering & fast shipping system. To keep our prices low, all cancelations are subject to a 5% cancelation fee to cover transaction processing fees. We reserve the right to charge up to a 10% cancellation fee for cancelled orders due to merchant fees, special order fees and the cost of processing and shipping orders.When you request a cancellation of an order or a part, please note that it may take time for a manufacturer to cancel an order if the order is drop-shipped. We also have to confirm that the product has not shipped. If the product has shipped then this must be processed as a return.Also note that sometimes products ship more quickly than expected, so we recommend that you do not purchase alternative products until receiving final confirmation of the cancellation.
Returns:We cannot accept returns on parts that have been used or installed. No returns will be accepted after 30 days. All Returns must be in original packaging. Prior authorization must be given before any return can be made. Up to a 25% Restocking Fee may apply. Special orders may be subject to Additional Manufacturer Restock Fees as well. Shipping cost will not be refunded.Hoods as well as PCM Programmers may not be returned unless defective and only for replacement. ALL returns must be first filed using our online form found here: https://www.lmperformance.com/returns.
Lost Order ClaimsAll lost order/package claims must be made within 5 days of the shipping date or tracking information delivery date. All claimes made after this date will not be accepted due to Shipping companies policies of filing loss claims.
Damaged Items or Incorrect Items: Please contact us right away if your item has been damaged in shipping or are incorrect. Please note that we will ship replacement items the same method of shipping the order was originally placed for. LMPerformance can not ship packages overnight at our cost if the original shipping was not also overnight. Claims must be filed in order for replacement parts to be shipped.
Warranties:Any warranty claims must be placed with the manufacturer. All of the products sold by LMPerformance, regardless of the manufacturer, are designed for Racing and Performance applications. Many of our manufacturers offer NO WARRANTY on their products, either stated or implied, due to the unusual stresses placed on the parts and because we have no control over how they are installed and used. Many of these products are designed for off-road use only and are not legal for use on public highways. If you have a question about the warranty on a specific product, please e-mail or call us. Buyer assumes all risk and liability associated with these products.
Installation:We are not responsible for or any costs associated with the installation or the improper installation of any products. Purchaser assumes the risk associated with the installation of products. We, along with the manufacturer of each product are not responsible for any direct or indirect damage to the vehicle, personal, or costs incurred from the use of products.
Starting at 0% Order Now, Pay Later Learn More.
