JLT Series 2 Cold Air Intake Kit Ford Mustang GT and Boss 302 Red Filter CAI2-FMG-11

ALL NEW JLT SERIES 2 for 2011-2014 Mustang GT 5.0 and 2012-2013 Boss 302.



Have an aftermarket manifold like a Boss or Sniper? Then this is your cold air intake!

This new kit was designed from the ground up to work with today's aftermarket manifolds and throttle bodies.

Released back in 2010, our original kit has worked great on the 5.0 for over 7 years. With the release of the BOSS and now the Holly Sniper along with 85 and 90mm throttle bodies we decided to do a redesign to accommodate these different sizes and angles.

The all new JLT Series 2!
BIGGER, BADDER and still the BEST!

Designed to fit and work with the stock manifold as well as the BOSS and Holley Sniper.

It starts with a 4 opening at the throttle body to match up to those 90mm units.The kit comes COMPLETE with 2 couplers. One 4 straight for the 90mm and a 4-3.5 reducer for the stock unit.

Next is the perfect 112mm MAF housing. Up from 107mm on the original, but not so big to cause drivability issues. Oh and the MAX allowed in NMRA Coyote Stock racing.

At the MAF you attach our one off designed S&B filter. A massive 5 at the inlet with a full radiused bellmouth to huge 1 deep pleats, this thing flows tons of air.

Finally all this sits in our own designed Roto Molded heat shield that utilities the factory fresh air inlet to get you the most cool air possible.

Finish it off with a silicone coupler and stainless clamps and you got the BEST Intake on the market!!! NO METAL TUBING HERE!!.

MOLDED IN MAF
It’s a full 112mm ID at the MAF area.
MAF is rotated to the inside or engine side of the tube for a more pleasing smooth look.

HEAT SHIELD
Includes roto molded plastic heat shield to block engine heat at idle and low speed
It incorporates the fresh air inlet from the grill.
It uses a large area to make sure the filter has tons of cool air.

KIT INCLUDES:

• JLT Intake Tube with Black Textured finish
• 4 Silicone Coupler for aftermarket throttle bodies
• 4-3.5 Silicone reducer for stock throttle bodies
• 5x7 S&B Powerstack Air Filter
• Roto molded Heat Shield
• HD Clamps, 2013-14 hood insert plug & all needed hardware

This product is NOT CARB (California Air Resource Board) Exempt. It is not for legal sale or use in the state of CA or any other states adopting CA emission standards and require a CA Executive Order (EO) number. Any orders placed for this item with a CA ship to address will be cancelled.

All Red Filters are OILED Filters

JLT cold air intakes are made right here in the USA. JLT PERFORMANCE was founded in 2004 and is located in Chesapeake, Virginia where they manufacture not only primo cold air intakes but impressive oil separators for late model Mustangs, Camaros, Mopars and Ford Trucks.

You know that a cold air intake serves the purpose of moving the air filter outside of the engine compartment and away from unnecessary heat thus it allows cooler air and more oxygen into your car’s combustion chamber and as a consequence your car has more power. But not all cold air intakes are created equal and JLT cold air intakes like the direct replacements for 1996-2004 Mustangs, 1997-2003, 2015-2917 Ford trucks and 2005-2018 Mopar cars will require no tuning. If you have a 2005 and newer Ford or Camaro because JLT has complete packages with tuners and custom tunes so you can install it all at home in less than one hour. You won’t find any choke points nor will there be any accordion style bends resulting in a minimum of restriction with these air intakes and because the JLT intakes only draw air from outside the engine bay your car’s engine gets maximum air density which should improve mileage under almost all driving conditions.

JLT also developed a uniquely designed oil separator that filters and separates the oil in the vapor so that it is deposited into a catch can rather than in your car’s intake system. Although the oil separator will work on any engine JLT looked out for their Ford, Mopar and GM customers in particular by designing a plug and play set up that will work on most applications with PCV lines already attached so installation should only take about a minute..

IMAGES: Images may be a representation and may not reflect the actual product.