JLT Cold Air Intake Hellcat Challenger 6.2L CAI-HC-15

JLT Cold Air Intake Hellcat Challenger 6.2L, JLT Cold Air Intake Hellcat Charger 6.2L

JLT Cold Air Intake Hellcat Challenger 6.2L, JLT Cold Air Intake Hellcat Charger 6.2L

Here kitty kitty! JLT HELLCAT Cold Air Intake (2015-19 6.2L Charger/Challenger)

15-20 RWHP and No Tune Required!

JLT has jumped into the Hellcat intake market with both feet. We have owned a 2016 Hellcat Charger for nearly a year now and have been testing and designing this kit the entire time.

This JLT Hellcat intake kit includes a fully Roto Molded airbox that uses the factory fresh air (Ram Air) inlet from the grille/headlight that also seals to the hood. We feel this is the key component that puts our kit well above the rest. Not only does this box help keep inlet air temps down by blocking the filter from hot engine heat, it also helps hold in the cool air getting rammed in from the inlet creating a high pressure area around the filter.

Speaking of the filter, our filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1 deep pleats for more surface area than filters that look much bigger.

The tube on this Challenger cold air intake is roto molded plastic with a huge 125mm for superior airflow and NO heat soak like metal tubes.
With a mouth of 4.5 at the throttle body end, it is ready for any larger throttle bodies that may come in the future.

MAF and IAT adaptor plates
2015/16 Hellcats have a Mass Air Flow sensor and 2017-2019 have an Inlet Air Temp sensor. We designed our kit to work with BOTH. Included in each kit are CNC machined aluminum plates, gasket and stainless screws to adapt to either model years.

HEAT SHIELD
Includes new roto molded plastic heat shield to block engine heat at idle and low speed.

RAIN SHIELDS
Each kit comes with custom designed and water jet cut Lexan shields that bolt to the hood grille. Not only do they keep rain from the filter, they allow the cooler rammed air to stay in the box around the filter VS just being pushed out of the grille.

FEATURES:

Incorporates fresh air inlet from the grill.

Uses a large area to make sure the filter has tons of cool air.

Kit includes:

JLT Plastic Intake Tube

Silicone Reducer

5x7 S&B Powerstack Air Filter

Roto molded Heat Shield

JLT MAF adaptor plate

JLT IAT adaptor plate

JLT Charger Rain Shield

JLT Challenger Rain Shield

HD Clamps & all needed hardware

2019 Hellcat PCV Kit

GAINS AND TESTING
15-20 RWHP can be expected on a stock Hellcat
25-30+ can be expected on a pulley and tuned Hellcat

TUNING
No tuning required

EASY INSTALL
The design, detailed instructions and online video (see below) helps make this an easy install (see Instructions & Videos tabs to download / view).

AIR FILTER OPTIONS - OIL OR DRY
We use only the best air filters made by S&B to our specifications.
For years we only used oiled filters, but dry filter technology has been proven and is now a popular option.

Should I choose a Dry Disposable or Cotton Oiled Filter?
Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it.

Dry:Comparable airflow to oiled cotton filters with the same great protection.
Last for up to 30, 000 miles of highway driving. Extend the life of the filter using compressed air.

Oil: Oiled filters can last forever as long as you properly clean and re-oil it.
Oil filters are available in red or blue and Dry filters are white.

RACE FILTER:The Race filter is an optional filter, this filter IS NOT FOR STREET USE! It's no filtering media, with prolonged use it will allow contaminated that can damage your engine! JLT Performance will not be responsible for any damage from use of Race filter. Customer assumes all risk!

MAINTENANCE
To properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.
*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again.

JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!

TESTING
We wanted to do as much testing as possible, so we sent kits to some of the best in the Hellcat business.

*This product is NOT CARB (California Air Resource Board) Exempt. It is not for legal sale or use in the state of CA or any other states adopting CA emission standards and require a CA Executive Order (EO) number. Any orders placed for this item with a CA ship to address will be cancelled.

CARB E.O. # D-761-4 and will include a CARB decal with each kit starting March 3rd, 2020

All Red Filters are OILED Filters

JLT cold air intakes are made right here in the USA. JLT PERFORMANCE was founded in 2004 and is located in Chesapeake, Virginia where they manufacture not only primo cold air intakes but impressive oil separators for late model Mustangs, Camaros, Mopars and Ford Trucks.

You know that a cold air intake serves the purpose of moving the air filter outside of the engine compartment and away from unnecessary heat thus it allows cooler air and more oxygen into your car’s combustion chamber and as a consequence your car has more power. But not all cold air intakes are created equal and JLT cold air intakes like the direct replacements for 1996-2004 Mustangs, 1997-2003, 2015-2917 Ford trucks and 2005-2018 Mopar cars will require no tuning. If you have a 2005 and newer Ford or Camaro because JLT has complete packages with tuners and custom tunes so you can install it all at home in less than one hour. You won’t find any choke points nor will there be any accordion style bends resulting in a minimum of restriction with these air intakes and because the JLT intakes only draw air from outside the engine bay your car’s engine gets maximum air density which should improve mileage under almost all driving conditions.

JLT also developed a uniquely designed oil separator that filters and separates the oil in the vapor so that it is deposited into a catch can rather than in your car’s intake system. Although the oil separator will work on any engine JLT looked out for their Ford, Mopar and GM customers in particular by designing a plug and play set up that will work on most applications with PCV lines already attached so installation should only take about a minute..

IMAGES: Images may be a representation and may not reflect the actual product.